De-sta-co 300IOC Bedienungsanleitung PDF herunterladen

CAMCO IOC

AUTOMATIC

OVERLOAD CLUTCH

NOTE: Camco does not Preset Input Overload

clutches at the factory. Input Overload Clutches can

only be properly set under fully loaded, field conditions.

(The numbers on the clutch face do not indicate any

torque valve, they are for reference only.)

The following instructions assume that the input

overload clutch is assembled on the cam shaft and the

overload limit switch is properly positioned. (If these

starting conditions do not exist, Please contact the

Factory.) Please refer to figures 1A and 1B when

starting.

Field Installation and Setting

STEP

Remove the Shut-off Spool #12. (Press fit if

necessary) Loosen Conepoint Set Screw #10.

(There are 1 or 2 possible tapped holes, but

use only one set screw. Explanation later.)

Reset limit switch.

STEP

When the match marks do not move under

power for one index, continue to run Indexer

for 5 to 7 indexes and stop in dwell. Repeat

the 5 to 7 index cycle 2 more times. If the

match marks have not moved, tighten Set

Screw #10. (The cone Point set screw must

enter the grove between the threaded areas.)

STEP

Now power indexer again and apply E stop in

mid-motion. The match marks should now

displace form 1/8” to 2”, depending on the

size of the IOC. This step is necessary to

verify that the clutch has not been set too

tightly. If movement appears to be too much,

move Set Screw #10 to the other tapped

hole. This will permit additional tightening of

only 1/2 notch.

STEP

Re-position shut off spool #12 to center of

radial grooves in thrust head #4. This should

reset the overload stop switch.

The unit is now ready for continued operation. The

above procedure should be repeated if the loading

changes. Any inconsistencies with the above procedure

should be referred to your Camco Representative or the

Camco Factory.

STEP

Tighten the Adjusting Nut #3 to firm tightness.

Use a spanner wrench in sizes through 350

IOC, or crescent wrench with Removable

Pinion #15 in size 400 IOC or larger. NEVER

power a unit with a loose clutch! Severe

Indexer damage can result! Manually rotate

cam shaft to the mid-dwell position. Use a felt

tip to register match marks per figure 2.

STEP

Power indexer drive for 1 index and observe

match marks. If the marks have separated –

1. Wipe off old marks.

2. Retighten nut one or two notches.

3. Register new match marks.

STEP

Repeat step 3 if marks separate.

1 2 3 4

Inhaltsverzeichnis

Seite 1 - OVERLOAD CLUTCH

®CAMCO IOCAUTOMATICOVERLOAD CLUTCHNOTE: Camco does not Preset Input Overloadclutches at the factory. Input Overload Clutches canonly be properly set u

Seite 2 - FIGURE 1A

®350 IOC and SmallerRepair Parts List Advise clutch size and CAMCO serial number.1 Housing2 & 5 Thrust Head & Friction ConeAdvise bore size a

Seite 3 - FIGURE 1B

®400 IOC and LargerRepair Parts ListAdvise clutch size and CAMCO serial number.1 Housing2 Friction Cone3 Adjustment Nut4 Thrust HeadAdvise bore size a

Seite 4 - FIGURE 3

®Scribe match mark lines on adjusting nut and innersleeve. Lines should not move in normal cycle, but shouldseparate 1/8” to 2” in jog, depending on s

Verwandte Modelle: 225IOC | 200IOC | 180IOC |

Kommentare zu diesen Handbüchern

Keine Kommentare

De-sta-co 300IOC Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware De-sta-co 300IOC herunter. DE-STA-CO 300IOC User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 225IOC | 200IOC | 180IOC |

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware De-sta-co 300IOC